Laser-based technique for controlled damage of mesenchymal cell spheroids: a first step in studying reparation in vitro

ABSTRACT Modern techniques of laser microsurgery of cell spheroids were used to develop a new simple reproducible model for studying repair and regeneration in vitro. Nanosecond laser pulses (wavelength 355 nm, frequency 100 Hz, pulse duration 2 ns) were applied to perform a microdissection of the outer and the inner zones of human bone marrow multipotent mesenchymal stromal cells (BM MMSC) spheroids. To achieve effective dissection and preservation of spheroid viability, the energy of laser pulses was optimized and adjusted in the range 7-9 μJ. After microdissection, the edges of the wound surface opened and the angular opening reached a value of more than 180°. The destruction of the initial spheroid structure was observed in the wound area, with surviving cells changing their shape into a round one. Partial restoration of a spheroid form took place in the first six hours. The complete structure restoration accompanying the reparative processes occurred gradually over seven days due to remodelling of surviving cells.


INTRODUCTION
Regeneration is the restoration of the lost parts of the body, which can occur after injury at different levels of the organization: i.e. cellular, tissue, organ, structure or whole-body. There are several basic strategies for regeneration: remodelling of the remaining undamaged tissue in the absence of cell proliferation (morphallaxis); replacing the structure due to proliferation of a resident stem cells pool, as well as trans-and de-differentiated cells (epimorphosis); or, a combination of these two processes (Alvarado and Tsonis, 2006). Despite the conservatism of general mechanisms of regeneration in evolution, mammals have almost lost the ability to fully restore vast areas of the body after injury (Bely, 2010;Bely and Nyberg, 2010).
In modern biology, for the model investigation of repair and regeneration, researchers are actively moving from two-dimensional (2D) to three-dimensional (3D) conditions (Haycock, 2011).
Multicellular organisms have a 3D organisation, in which cells interact with other cells and an extracellular matrix to form a complex set of contacts, thereby creating a unique microenvironment. Behaviour, proliferative activity and physiological properties of the cells in 3D systems in vitro, in contrast to 2D monolayer, are similar to in vivo conditions (Cukierman et al., 2001). Various 3D cell cultures are now used to simulate tissue cytoarchitectonics and to create a model system that would resemble the structure of native tissue (Schmeichel and Bissell, 2003;Takezawa et al., 1992). In these 3D cultures, cells grow, interacting with the environment (other cells, extracellular matrix and the external environment) in all three dimensions (Antoni et al., 2015;Koch et al., 2012). In recent years, 3D cultures have been widely used for monitoring cell proliferation, analysis of viability, morphology and differentiation of cells in response to various stimuli, as well as studying cell-cell interactions, migration and invasion of tumour cells into the surrounding tissues (Kubatiev et al., 2015;Pampaloni et al., 2007).
Cellular spheroids are one of the most common options in ex vivo studies using 3D cell cultures, along with explant cultures, cells on microcarriers and tissue-engineered systems. They represent 3D spherical cell clusters, which self-organize due to natural adhesive properties. In spheroids obtained from single cell suspension, they not only make intercellular contacts but also contacts with newly synthesized extracellular matrix, thereby forming a structure, the organization of which resembles the organization of tissues in vivo (Lin and Chang, 2008). Many cell types have a natural tendency to aggregate; therefore, spheroids can be obtained from one or more cell types (Haycock, 2011). In particular, in their work, V.S. Repin and co-authors (2014) reveal a consistent pattern in the formation of spheroids from cells of epithelial and mesenchymal phenotypes.
The field of application of cellular spheroids is constantly expanding. For example, studying the mechanisms of wound healing is one of the challenging issues nowadays. Using in vitro monolayer cultures as a model system allows for studying only specific parameters of cell behaviour (rate of migration and proliferation, extracellular matrix synthesis), but does not allow for evaluating the contribution of intercellular interactions as well as interactions of cells with the extracellular matrix. Hence, similar studies are now performed mainly in vivo or by using organotypic explant cultures ex vivo (Antoni et al., 2015;Gottrup et al., 2000). Nevertheless, the search for simple reproducible model systems for studying mechanisms of regeneration, problems of the fibrotic and non-fibrotic wound healing continues. Repair of cellular spheroids after damaging effects could be one such model.
It has been established that if the diameter of the spheroid exceeds 200-250 μm, an oxygen concentration gradient appears, with a minimum at the centre of the spheroid (Curcio et al., 2007;Griffith, and Swartz, 2006;Acker et al., 1987). In addition, large spheroids accumulate carbon dioxide and cell waste products, resulting in the formation of necrosis in the centre of the spheroid. Therefore, to ensure proper diffusion of nutrients to the central region, we used cellular spheroids with diameters no more than 200 μm. Given the relatively small size of cellular spheroids, the development of a repair model on this object requires the use of the most advanced technologies. For this study, we chose to use the technique of laser microsurgery to simulate spheroid injury.
In current clinical practice and biology, laser microdissectors based on pulsed lasers have been widely used (Magidson et al., 2007). Using this technique makes microsurgery possible not only at tissue, but also at the cellular and even subcellular levels. Femtosecond laser sources are regarded to be the most promising. They provide high spatial and temporal resolution, and have greater penetration depth, which is extremely important, particularly for affecting interstitial structures. Femtosecond laser systems have been shown to be useful and successful in different fields: for dissection of the nuclei in fixed cells, actin filaments (Heisterkamp et al., 2005;Shen et al., 2005) and chromosomes (König et al., 2001;Uchugonova et al., 2012), as well as separating single living cells from the group (Kohli et al., 2005) and inactivation of cell organelles, such as mitochondria (Watanabe et al., 2004;Shen et al., 2005). These systems allow for not only the formation of incisions on cell membrane (Kohli et al., 2005), but also solving the problem of selective delivery of extracellular substances into cells (optoinjection and transfection) by using short-lived laser perforation of cell membrane (Il'ina et al., 2013(Il'ina et al., , 2014Baumgart et al., 2008;Uchugonova et al., 2008;. Stevenson et al., 2006). It should also be noted that, in recent years, the possibility of successful microsurgery of intracellular structures (individual centrioles, cytoskeletal elements, spindle microtubules) has been demonstrated by using nanosecond (Magidson et al., 2007;Khodjakov et al., 2004) and picosecond laser systems (Colombelli et al., 2005;Botvinick et al., 2004), with an accuracy comparable to that of femtosecond systems (Sacconi et al., 2005).
In addition to 2D structures (cell monolayers), laser microsurgery techniques have been tested on 3D objectsembryos of different organisms. In particular, a nanosecond laser dissector was used for creating a hole in oocyte zona pellucida for the further in vitro fertilization or polar body biopsy (Clement-Sengewald et al., 1996). Later, a laser dissector based on the femtosecond laser was successfully used for solving the problems of assisted hatching and dissection of trophectoderm cells during biopsy at the later stages of pre-implantation development (Ilina et al., 2016(Ilina et al., , 2015. In addition, picosecond and femtosecond laser pulses were successfully used in performing non-contact fusion and inactivation/enucleation of blastomeres in mouse (Karmenyan et al., 2009) and porcine (Kuetemeyer et al., 2010) embryos, as well as for studying the modulation of morphogenetic movements in Drosophila melanogaster embryos (Supatto et al., 2005). Despite the fact that embryos are 3D objects, they serve as convenient models only for a limited number of problems. Meanwhile, cellular spheroids, as a model object, allow us to bridge the gap between living tissue and 2D structures in vitro, creating prerequisites for the development of models of laser microsurgery based on cellular spheroids.
However, despite the interest of scientists regarding spheroids and widespread application of lasers in biology and medicine, there are currently only a few studies in which laser technologies are used for studying spheroids. These works are concerned with techniques of spheroid visualization and, in particular, methods of light-sheetbased fluorescence microscopy (Pampaloni et al., 2013;Bruns et al., 2012), two-photon microscopy for studying matrix-guided mechanisms of cell invasion (Ilina et al., 2011), or visualization of spheroids differentiation (König et al., 2011). According to our data, the only study in which the laser was applied directly to impact and locally damage the spheroid was found in the work of Uchugonova and co-authors (2007), who demonstrated the possibility of irreversible optical damaging of single cells, which migrated from the spheroid, while maintaining the viability of surrounding non-irradiated cells. Such a technique of selective laser destruction (knockout) can be used for 'optical cleaning' of cell cultures. In turn, the study of the characteristics of the spheroid repair process after large-scale 'extended' injuries has not been conducted to date.
The aim of this study, then, was to develop a reproducible model of cellular spheroids injury using laser microsurgery techniques and to investigate the repair process after laser impact. It was decided to use a nanosecond laser dissector to simulate spheroids damage. The energy of the laser pulses were optimized such that the dissection was carried out only in the specified area of the spheroid and, therefore, would not compromise the viability of the spheroid in general. The study was conducted on human bone marrow multipotent mesenchymal stromal cells (BM MMSC).

RESULTS
The cells in obtained BM MMSC primary culture under 2D conditions successfully formed a monolayer, maintained a high proliferative potential of up to the fourth passage, and had a characteristic spindle-shaped form. After four passages, BM MMSCs expressed characteristic mesenchymal markers (CD105, CD90 and CD29), while they almost did not express haematopoietic and lymphocyte markers CD45, CD34, CD14, CD11b, CD19 (Table 1).
Under non-adhesive 3D conditions, BM MMSC suspension successfully formed compact viable spheroids in seven days. Histological analysis revealed two distinct regions in compact spheroids: two to four layers of elongated surface cells and an internal core consisting of polygonal irregular cells. Imbricated cells of the surface region were in close contact with each other, whereas the inner zone was loose, and polygonal cells were separated by the extracellular matrix ( Fig. 1).

Injuring BM MMSC 3D cultures with nanosecond laser scalpel
The parameters of the laser radiation and, in particular, the energy of laser pulses were optimized to perform an effective microsurgery of selected regions of the surface and internal areas of the BM MMSC spheroid. The main 'surgical' mechanism causing tissue dissection after application of nanosecond laser pulses is the formation of plasma and optical-induced breakdown (Genc et al., 2014;Rau et al., 2006;Vogel et al., 1996). In their work, Genc and colleagues (2014) considered two modes of optical-induced breakdown formation, depending on the energy of laser pulses. In the first case, the energy of pulses was slightly higher than the threshold energy, while optical-induced breakdown was accompanied by the formation of cavitation bubbles the size of a few micrometres. Their emergence has led to visible damage to the irradiated tissue; but, due to the small size of cavitation bubbles, it became possible to perform localized microsurgery of the selected object. The second mode occurred after a considerable excess of pulse energy threshold, characterized by the visible plasma luminescence and formation of large cavitation bubbles (50-100 μm). When applied to spheroids, this mode was highly undesirable, as the precise dissection became practically impossible. The formation of large cavitation bubbles led to a massive and irreversible damage to the whole object.
In our experiments we determined, that the threshold energy of laser pulses, required for dissection to start, lay in the range of 6.2-6.6 μJ (the speed of motorized stage movement along xy axis was selected to be 120 µm/s). However, the quality of dissection was very sensitive to spheroid's size and heterogeneity of agarose plate thickness, where spheroids were placed. Application of laser pulses with higher energies led to more efficient spheroid dissection and reproducible results. Further increase in pulse energies (>9.1-9.2 μJ) caused the formation of a great number of cavitation bubbles and the chaotic displacement of the object from its initial position during laser exposure. As a result, the dissection of the spheroid chosen area could not be performed efficiently. Moreover, uncontrolled damage to the surrounding areas or spheroid might have occurred. Taking into account all the listed factors, the optimal energy of laser pulses was set in the range of 7-9 μJ, which corresponds to laser intensity of 1-1.2×10 10 W/cm 2 . The process of laser exposure and formation of cavitation bubbles, leading to visible damage in spheroids is demonstrated in Fig. 2B,C, white arrow. As a result of exposure to laser radiation, a spontaneous opening of the wound edges was observed ( Fig. 2; Movie 1). The schematic of spheroid obtaining and further laser exposure procedure, as well as indication of wound angular opening are presented in Fig. 2M.
Correlation between the change of angular opening of the wound surface and time (from 0 to 240 s after laser impact) was evaluated for 14 single spheroids. Immediately after microdissection, the wound edges opened up to 118±18°and, in the subsequent four minutes, increased up to 197±25° (Fig. 3). The further observed growth of angular opening was negligible.
We observed the formation of fragments of dead cells in the area of injury within the first hour after laser exposure ( Fig. 4A-C;  Fig. S1). The increase of angular opening of the wound edges was accompanied by a change in morphology of the cells at the wound surface, with their shape changing from elongated and flattened to the round one. The structure of the surface layer in the intact area remained virtually unchanged and retained its integrity, while the cells remained flattened (Fig. 4D-G).

Reparation of BM MMSC spheroids after the injury with nanosecond laser scalpel
The results of fluorescence microscopic, electron microscopic ( Fig. 4) and histological analysis (Fig. 5) showed that, within the first 60 min after microdissection, wound surface contained fragments of dead cells and rounded cells ( Fig. 4; Fig. 5A). In the area of injury, the original structure of spheroid was disrupted, and morphology of the surface and the inner zones became unified: i.e. the cells changed their shape and became polygonal or rounded. In uninjured regions of spheroids in the experimental group, the initial structure (surface area consisting of flattened cells and distinct from polygonal cells in the inner zone) were preserved (Fig. 5A). Directly in the area of damage, there were only single cells that maintained their original morphology; they were surrounded by cellular  debris, cell surface was rough and cytoplasmic integrity was compromised.
After six hours, the first steps of spheroid structure restoration were observed, but the surface cells in the area of injury remained polygonal (Fig. 5B). A day after the injury, spheroid structure was partially restored and cells in the surface layers began to flatten (Fig. 5C). By the third day, there was only one layer of flattened cells in spheroids of the experimental group, with the cells of polygonal shape still located deeper. Full restoration of the initial structure of the spheroids, with a few surface layers of flattened imbricated cells and polygonal cells of the inner zone, occurred seven days after microdissection (Fig. 5D). The described dynamics of repair were confirmed by the data obtained during live time-lapse microscopy of the experimental spheroids for seven days after laser microdissection ( Fig. 6; Movie 2). Furthermore, immunocytochemical staining against Ki67 (the marker of cell proliferation) at 24 h after injury, when the initial wound closure was taking place, showed that there were no cells in active phases of cell cycle (Fig. S2), and it was also noted that the resulting diameter of spheroid after repair was less than the initial one (data not shown).

DISCUSSION
Repair and restoration of tissues play an important role in the normal functioning of the body. Repair mechanisms and problems of their failure, such as scarring of the parenchymal organs and skin, are not fully understood. A long-surviving, simple, reproducible 3D cell systemi.e. spheroidallows for the maintenance of the viable, functional and physiological state of cells in the absence of exogenous humoral and endocrine factors. Developing a model of spheroid damage using microdissection technique opens up the possibilities to study the mechanisms of regeneration and the role of spheroid-forming cells in repair.
Obtaining multi-cellular spherical aggregates from embryonic stem cells in vitro was described over 70 years earlier. To date, spheroids from embryonic stem cells, oncogenic lines, and transformed and primary cultures of different cell types have been obtained and characterized. Intercellular adhesion, cell-matrix   . At 6 h, initial steps of integrity recovery were already taking place, so that wound edges became indistinguishable (B). At 24 h, the surface layer was closed (C) and by the seventh day the initial spheroid structure was fully recovered (D). Arrows indicate wound edges. Semi-fine sections, stained with methylene green, light microscopy. adhesion, cytoskeletal and extracellular matrix-mediated factors act as basal factors to maintain the shape of spheroids in response to external forces, including gravity and hydrophobic-hydrophilic interactions. In addition, it is known that 3D cultures promote preservation and maintenance of the cells' ability in relation to differentiation and morphogenesis (Cesarz and Tamama, 2016). Under 3D conditions, cells retain the nuclear-cytoplasmic ratio and the ratio of the cytoplasm volume to the membrane area characteristic of in vivo conditions, which is required for successful functioning and communication (Baker and Chen, 2012), making cells more stable than in regularly passaged 2D monolayer cultures (Antoni et al., 2015). Different culture systems, such as 'hanging drop', nonadherent microplates, nonadherent and modified surfaces and rotary bioreactors, are used for obtaining cellular spheroids without the addition of the exogenous matrix (Benien and Swami, 2014;Kelm et al., 2003). Regardless of the technique used, mesenchymal cells from various sources are capable of forming viable dense spheroids under 3D conditions (Cesarz and Tamama, 2016;Repin et al., 2014;Zimmermann and McDevitt, 2014;Saburina et al., 2013).
Up to date, MMSC from adult bone marrow stroma are the bestcharacterized mesoderm-derived stromal cells with multipotent differentiation capacity. Moreover, MMSCs are known to possess strong immunomodulatory and anti-inflammatory properties and thus may contribute to tissue repair structurally and by modulation of local environment (Klimczak, Kozlowska, 2016).
It was shown that, after seven days in 3D culture, BM MMSC single cell suspension formed spheroids with a dense zone of flattened cells at the surface and irregular shaped central cells (Frith et al., 2010). In addition, the cultivation of BM MMSC under 3D conditions stimulated an active expression of mitogens, angiogenic and anti-inflammatory factors, and numerous cytokines (Cesarz and Tamama, 2016;Heo et al., 2016;Bartosh et al., 2010). Previous studies into the selection of optimal conditions for self-assembly of different types of cells in the 3D system influenced by gravitational forces and data about structure of obtained spheroids Repin et al., 2014) are consistent with the present data. The obtained seven-day BM MMSC spheroids (with 150-200 μm diameter) consisted of two to four layers of dense flattened surface cells and a loose inner zone containing polygonal cells and the extracellular matrix. This obtained and highly reproducible spheroid structure, resembling epithelial and mesenchymal tissue components, as well as described properties of BM MMSC cell population, led us to choosing these objects as a model for studying regeneration processes in vitro.
The developed model of laser microdissection and optimally chosen conditions of laser exposure allowed us to damage the surface and the inner area in a selected region of spheroid without disturbing the viability of the object in general. At the selected modes of laser irradiation, a lot of cell fragments appeared in the wound area of a spheroid, which is directly related to the physical effects, while a spheroid in the uninjured area retained the initial structure. The angular opening at the wound surface increased by more than 70°in the first four minutes after laser impact, which partially contributed to the rapid clearing of the wound from dead cells and their fragments. Such a change could indicate an artificial mechanical stress relaxation, which plays an important role in embryogenesis, morphogenesis and differentiation (Fouchard et al., 2014;Belousov et al., 1999). Spheroids are relatively soft, inelastic structures, in which the balance between cell-cell adhesion, cellmatrix adhesion, cytoskeletal and extracellular matrix-mediated factors may change as a function of time. In structures formed using scaffold-free, non-adherent systems, cells organize cortical cytoskeleton, which can dynamically change under different tensions (Czajka et al., 2014). In 30 min after microdissection, cells at the edges of the wound area acquired a rounded shape, which is probably due to loss of intercellular junctions and cytoskeleton reorganization. Mechanical stress relaxation caused by microdissection was likely to lower the surface tension and, therefore, contributed to the rapid changes in cell shape. The appearance of debris around the wound area could have appeared due to a partial loss of rounded cells caused by detachment-induced apoptosisanoikis (Grossmann, 2002).
The sphere is the 'default' tissue morphology under non-adherent conditions, by having the smallest surface area per unit volume (cell). Minimal surface area translates into minimal interfacial tension and, therefore, the lowest energy requirement to maintain. Indeed, we observed a recovery of the spherical shape of spheroids in the first hours after injury. The internal structure of spheroids recovered gradually and, within seven days, cells in the irradiated area gradually acquired the initial morphology, the dense layered structure of the surface zone with flattened cells was restored and the repair processes were complete. We noted that spheroids contained no proliferating cells and the diameters of spheroids repaired after microdissection decreased compared to the initial ones, while the edges of the wound did not close, the defect seemed to be filled with undamaged cells of the inner zone (Movie 2). In this regard, we can assume that the repair of BM MMSC spheroids after microdissection is performed not as a result of cell proliferation, as in epimorphic regeneration, but due to the remodelling of existing viable cells.

Conclusions
Studying regeneration in vitro using monolayer cell cultures allows us to evaluate only proliferation and migration of cells, and only in one plane. Hence, models accounting for 3D complex interaction of cells with each other and with the extracellular matrix are required for a detailed understanding of regeneration processes. In vivo experiments on animals represent one such model, but they are timeconsuming, not always available, costly and poorly reproducible due to multiple factors. We have proposed a new simple reproducible model for studying regeneration in vitro in 3D cell spheroids. This system allows us to combine cells of different phenotype, origin, etc., to vary the supplements to the basal growth media, which, in combination with the innovative technology of laser microdissection, opens up opportunities for searching and exploring new ways to stimulate repair.

2D cell culture for cell spheroids technique
Primary cultures of human BM MMSC were used in the experiment. Samples of the bone marrow were obtained after voluntary written informed consent of patients. All the procedures were approved by the Ethical Committee of Federal State Budgetary Scientific Institution 'Institute of General Pathology and Pathophysiology', while performed in accordance with the Helsinki Declaration.
At 70% confluence, cells were passaged, with the fourth passage cultures used for immunophenotype analysis and spheroid formation.

3D culture, obtaining cell spheroids
To obtain spheroids in 3D culture conditions, suspensions of characterized BM MMSCs at the fourth passage were placed in agarose plates with microwells (Microtissue, USA) at 250,000 cells/ml concentration in complete growth medium. Agarose plates were transferred to wells of 12-well plates and were cultured for seven days under standard conditions (37°С, 5% СО 2 ).

Laser dissector
Spheroids were irradiated using the Palm CombiSystem (Zeiss, Germany) nanosecond laser scalpel (wavelength 355 nm, repetition rate 100 Hz, pulse duration 2 ns, pulse energy was varied in the range of 7-9 μJ, the speed of motorized stage movement 120 µm/s). Laser radiation was focused on the objects using micro-objective Zeiss Fluar (10×, NA 0.5). The focused spot radius was estimated to be ∼3.3 µm. PALM RoboPro software was used to control laser scalpel.

Nanosecond laser BM MMSC spheroids microsurgery
The surface and inner spheroid layers were injured with nanosecond laser pulses. Laser dissection of spheroid layers was performed by applying laser pulses along the straight-line path (from spheroid periphery to the centre) as defined by the operator in the PALM RoboPro software. The length of laser irradiated path was chosen for each spheroid individually and was set to be equal to its radius (typically, 75-100 µm). The laser processing of the defined straight-line path was repeated for five to eight times. Every next cycle was characterized by the axial (along z-axis) laser beam focus shift to provide the dissection of spheroid in three dimensions. The schematics of experiment is presented in Fig. 2M, and the process of microdissection is shown in Movie 1. The dynamics of spontaneous reparation after irradiation were observed using light time-lapse microscopy and, in the first hour after injury, the angles of wound opening were measured using AxioVision 4.8 software (Zeiss, Germany). The results were analysed using distributionfree analogue of repeated measures method, also known as the Fridman test.
A total of 25-30 spheroids were irradiated in every agarose plate, which took approximately 30 min. After irradiation, spheroids from experimental and control groups were returned under normal conditions in a СО 2 incubator (+37°С, 5% СО 2 ) for further observation of the wound healing process, or were fixed for histological studies. The design of the study, including the number of objects in experimental and intact groups as well as the different types of analysis methods used, are represented in Table 2. Spheroids were fixed at 30 min, 1 h, 6 h, 24 h, 3 days and 7 days after laser microsurgery.

Time-lapse microscopy
The first 60 min after laser microsurgery time-lapse, microscopy was performed using the PALM CombiSystem installation (Zeiss, Germany) with photorecording every five to 10 s for the first 5 min after irradiation and later every 5 min.
Long-term live registration was performed for seven days after laser microsurgery under standard conditions (37°С, 5% СО 2 ) in the chamber of time-lapse system Cell-IQ (CM Technologies, Finland), with photorecording every 20 min using Cell-IQ Imagen software. Images obtained were later analysed using Cell-IQ Analyzer software.
Semifine sections (1-2 μm) were obtained using ultra microtome Leica EM UC6 (Austria) and stained with methylene green (Sigma, USA) for 2-3 min. Specimens were observed under a light microscope Olympus ВХ51 (Olympus, Japan) using a Color View II photo camera, while software Cell F was used for photorecording.
To study spheroids under a scanning electron microscope, the fixed and dehydrated specimens were exposed to critical point drying, mounted on an object table and laid over with fine gold particles. The resulting replica was analysed under a CamScan (Japan) scanning electron microscope.

Cell viability analysis of spheroids after injury
One hour after laser microdissection spheroids were stained with fluorescent dye bisbenzimide for nuclei staining (3.2 nM/ml, 15 min, 37°C, Hoechst 33342; Fluka, Switzerland) and with propidium iodide for vitality assay (1.7 μM/ml, 15 min, 37°C; ICN Biomedicals, USA). The same spheroids were then stained with a cell-permeant dye Calcein AM to detect viable cells (5 min, 25°C; Thermo Scientific, USA). The results of staining were immediately analysed in visible and UV light under the Palm CombiSystem (Zeiss, Germany) and the Olympus Fluoview FV10I laser confocal scanning microscope (Olympus).